These days, clip on flip up sunglasses are the in thing because not only are they very stylish, but they are also very handy to use as compared to a real pair of sunglasses. The great thing about this type of thing is that one does not necessarily need to buy one because it is so easy to make one right at home. So if one would want to try making one, then here are some instructions how.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
Once he has straightened it out, then the next thing he should do would be to cut the wire in half so that he has two pieces. Now he should take one of the wires and slot it into the place where the arms of the glasses used to be. He should also do the same thing with the other side.
After the wires have been slotted in, then the next thing that one should do would be to actually tie the wires to the holes. The thing about this is that it is very hard to tie the wires by hand because these things are really tough. So in order to make a tight knot, one should use pliers to be able to tie the wire so that it will not be loose later on.
From there, take the two ends and place them in the center top part of the glasses. Always remember to embed the wires to the frame to make sure that the wire will be invisible to the eyes of the public. Once this is done, tie the two ends together in order to make a small clip in the middle.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
Once he has straightened it out, then the next thing he should do would be to cut the wire in half so that he has two pieces. Now he should take one of the wires and slot it into the place where the arms of the glasses used to be. He should also do the same thing with the other side.
After the wires have been slotted in, then the next thing that one should do would be to actually tie the wires to the holes. The thing about this is that it is very hard to tie the wires by hand because these things are really tough. So in order to make a tight knot, one should use pliers to be able to tie the wire so that it will not be loose later on.
From there, take the two ends and place them in the center top part of the glasses. Always remember to embed the wires to the frame to make sure that the wire will be invisible to the eyes of the public. Once this is done, tie the two ends together in order to make a small clip in the middle.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
About the Author:
You can visit the website www.brimzsports.com for more helpful information about How To Make Clip On Flip Up Sunglasses
